Error Codes

  • Updated on Oct 29, 2024
  • Published on Jul 8, 2021
  • 7 minute(s) read
  • Jonathan Poole
 Prev Next

The following table provides a description of all system error codes and associated error messages.

Code System Error Codes
1000 Unknown SYSCTL command.
1001 Unsupported SYSCTL command.
1002 Invalid SYSCTL command size.
1003 Feature not enabled.
1100 Stream exist, PID already in use.
1101 Stream does not exist.
1102 Stream is static, operation not permitted.
1103 Stream is free, operation not permitted.
1104 Unknown stream type.
1105 Failed to alloc stream control block, too many streams.
1106 Failed to alloc stream window.
1107 Failed to alloc bandwidth or packet rate too high.
1108 Failed to alloc report packet.
1109 Failed to alloc filter packet.
1110 Failed to alloc RTP port entry.
1111 Failed to free RTP port entry.
1112 Failed to alloc UDP port entry for external sender.
1113 Failed to free UDP port entry for external sender.
1114 Failed to alloc DVB receiver.
1115 Signature conflict, filter may not be unique.
1116 Device is down (link down).
1117 Failed to alloc packet buffer.
1118 Destination unreachable.
1119 Invalid STREAM message type.
1120 Stream in invalid state.
1121 Configured bandwidth to small or zero.
1122 Configured payload size to small or zero.
1123 This encapsulation is not supported.
1124 The requested resource is busy (already in use).
1125 Illegal destination address.
1126 Illegal source address.
1127 Invalid IP protocol version.
1128 Stream is in running state.
1129 Port conflict, port is used by another peer or function.
1130 Protocol conflict, port is used by another protocol.
1131 Failed to allocate port map entry.
1132 Stream is not in IDLE state.
1133 No media detected or link down.
1134 Invlaid port number. Port cannot be zero.
1135 Please use another port number, port is in the Ephemeral port range.
1136 Unknown sampling function.
1200 No dummy device.
1201 No outgoing device.
1202 No route to destination or outgoing interface conflict.
1203 Outgoing device is not configured with an IP address.
1204 Requested outgoing device conflicts with probe’s routing table.
1205 Link is down.
1301 Failed to alloc sync request.
1302 Failed to alloc filter packet.
1303 Failed to alloc report packet.
1304 PTS syncer is busy, try again.
1310 SNTP syncer is busy, try again.
1311 Failed to alloc filter packet.
1312 Failed to alloc report packet.
1400 Another Agent is running, operation not permitted.
1401 Agent is running, operation not permitted.
1402 Agent is not locked.
1403 Agent is locked.
1800 Unknown device or interface.
1801 Invalid device or interface name.
1900 Pool size exceeded, too many sessions.
1901 Too many sessions, failed to alloc session peer.
1902 Interface does not exist.
1903 Max number of VLAN interfaces exceeded.
2800 see errno message.
2900 Failed to alloc work-area.
2901 Invalid or unknown argument.
2902 Failed to create pid file.
2910 Device/interface does not exist.
2911 Device/interface is not up and running.
2912 Virtual interface has no physical interface.
2913 Device/interface is not configured with an IP address.
2914 Route to destination does not exist.
2915 Failed to resolve L2 address.
2916 Device/interface IP address conflicts with requested IP address.
2917 Invalid source IP address.
2918 Invalid destination IP address.
2919 Invalid route, outgoing device/interface conflict.
2930 Unknown stream type.
2931 Unknown stream encapsulation.
2932 Failed to create encapsulation template.
2933 Invalid session id.
2934 Invalid bandwidth.
2935 Unsupported protocol.
2936 Kernel stream ID is valid, e.g. this stream may already be running.
2939 Invalid source port (port=0).
2940 Invalid destination address.
2941 Invalid source address.
2942 Invalid GRE key (VPNID).
2943 Destination address is not a multicast address.
2944 Measurement Rx peer can’t listen on External Tx peer.
2945 Lite Rx peer can’t listen on External Tx peer.
2946 Ping reflector is external, use ICMP encapsulation.
2947 DVB Rx peer can’t listen on Prosilient Tx peer.
2948 Invalid IPTTL (ttl=0).
2949 Invalid STREAM message type.
2950 Failed to open UDP socket.
2951 Failed to open TCP socket.
2952 Failed to open raw socket.
2953 Failed to connect.
2954 ceUnknown device/interface.ll
2955 Unsupported device/interface.
2956 Invalid frame/packet rate.
2960 Address is reserved (for internal use).
2961 Payload size too small, not enough space to hold stream message.
2962 Invalid destination MAC address.
2963 Invalid source MAC address.
2970 Unknown or unexpected command.
2971 Invalid command version.
2972 Invalid command tag.
2980 Invalid probe Id.
2990 Unknown ITU-T Y.1731 PDU type.
2991 Frame-size too small.
2992 Packet-size too small.
2993 Invalid report IP address.
2994 No report interface.
3000 Fail to parse XML command.
3001 Too many clients, reject connection.
3002 XML dtd check fail, mismatch XML string to dtd.
3003 Failed to allocate xml parse tree.
3004 General failure, e.g. XML syntax error.
3005 Invalid XML version.
3006 XML buffer overflow.
3007 XML attribute syntax error.
3100 Illegal probeId received.
3101 Illegal caseId received.
3102 Agent engaged by other case.
3103 Non valid parameter sent to probe.
3104 Parse error.
3105 Agent not locked by case.
3106 Invalid system command end. 3107
3107 Evaluation period has expired.
3108 Fail to start agent application.
3220 Max number of peers exceeded.
3221 Allocate memory for peer.
3222 Failed to setup forwarding information via interface name.
3223 Failed to resolve IP address via interface name.
3224 No syncer exist to destination probe.
3225 Invalid reference, i.e. null pointer.
3226 Failed to perform multicast join.
3227 Failed to perform multicast leave.
3228 Peer id already exist.
3229 Non valid parameter.
3230 Peer does not exist.
3231 Failed to start Tx peer.
3232 Failed to start Rx peer.
3233 Failed to start Rx Zap peer.
3234 Non valid Zap interval.
3235 Failed to get next Zap channel.
3236 Zap flow run into trouble.
3237 Peer command queue too long, message discarded.
3238 Failed to start Ping peer.
3239 Zero packets received. Measure path down or reflector not respond.
3240 Failed to start peer.
3241 Zero packet train received. Measure path down or reflector not respond.
3300 Zero packets received. Measure path down or Tx flow stopped.
3301 To few packets received to analyse data.
3302 Result not within valid range probably due to inproper synchronization.
3303 Data not analyzed due to unreliable synchronization.
3304 Fail open analyze result file.
3305 Null ptr when analyze data.
3306 Received unexpected large jump in packet sequence number or received unexpected large number of packets.
3307 Zero packets received. Measure path down or reflector not responding.
3308 Lost packets metrics are estimated due to zero packets received. Measure path down or Tx flow stopped.
3309 Lost packets metrics are estimated due to zero packets received. Measure path down or reflector not responding.
3310 Estimated lost packets metrics exist due to zero packets received at end of interval.
3311 Estimated zero packets sent downlink from reflector. Measure path down or reflector not responding.
3312 Twamp-control connection disconnected (Premature close of twamp control reflector).
3314 Failed to connect, Init connection.
3316 The tunnel is down (Zero packets received. NFV tunnel is down).
3400 Failed to open UDP logging socket.
3401 No such directory.
3402 Failed to open log file.
3500 Agent crash by SIGNAL.
3501 Agent failed to start, failed to open ramdisk.
3502 Agent failed to start, failed to open pidfile.
3503 Agent failed to start, loopback interface not configured.
3504 Agent failed to start, loopback interface is down.
3505 Agent failed to start, management interface not configured.
3506 Agent failed to start, management interface is down.
3507 Agent failed to open control socket.
3508 Agent failed to init multicast socket.
3509 Agent was terminated by force.
3510 No Agent is running on this probe.
3511 Probe was acquired/stolen by another case.
3512 Too few packets to analyze in result record.
3513 Too many packets to analyze in result record.
3514 Result record statistics interval too short.
3515 Result record statistics interval too long.
3600 No packets received, join failed or Tx flow stopped.
3601 Packets received before called multicast join.
3602 Packets received after max join time elapsed, join latency high.
3603 No packets before called multicast leave, Tx flow probably stopped.
3604 Packets received after max leave time elapsed, leave failed or leave latency high.
3700 Max number of syncs exceeded.
3701 Allocate memory for sync.
3702 Enqueue sync.
3703 Sync entry already exist on probe.
3704 Setup forward info via if name.
3705 Sync does not exist.
3706 No sync connection to remote probe.
3707 Losing synchronization to remote probe. Connection bad or down.
3708 Failed to start synchronization.
3709 Sync command queue too long, message discarded.
3800 Time command queue too long, message discarded.
4000 see errno message.
4001 Timeout reading reply from ptexport daemon.
4002 Invalid reply from ptexport daemon.
4003 Failed connect to ptexport daemon.
4004 Invalid input request message format.
4101 Failed to connect to SDC server daemon.
4102 Failed to connect to DB.
4103 Invalid expression format.
4104 Filter gives no resulting data.
4105 SDC has no active Case.
5000 No measurement (gap) condense.
6000 No such entity.
6001 Password required.
6002 Probe configuration incomplete.
6003 Probe connection in wrong state.
6004 Transaction timeout.
6005 Parameter problem.
6006 Connection not open.
6007 Database error.

© 2025 Cisco and/or its affiliates. All rights reserved.
 
For more information about trademarks, please visit: Cisco trademarks
For more information about legal terms, please visit: Cisco legal terms
For legal information about Accedian Skylight products, please visit: Accedian legal terms and tradmarks