Configuring Interface Types and VLAN Mapping

This article describes the configuration of interface types and mapping of VLAN.

CLI Configurations

At Switch2

• Set the interface as CustomerEdgePort.
  your product(config)# interface gigabitethernet 0/2
  your product(config-if)# bridge port-type customerEdgePort

• Create the VLAN and make interfaces as member ports of this VLAN and Port P2 as untagged member.
  your product(config)# vlan 4
  your product(config-vlan)# ports gigabitethernet 0/2,0/3,0/4,0/5 untagged gigabitethernet 0/2

• Configure the CVID Registration table for the interface with CVLAN to map with SVLAN.
  your product(config)# interface gigabitethernet 0/2
  your product(config-if)# switchport dot1q customer vlan 2
  your product(config-if)# switchport customer-vlan 2 service-vlan 4 untagged-pep false

• Configure the interface type as providerNetworkPort.
  your product(config)# interface gigabitethernet 0/3
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit
  your product(config)# interface gigabitethernet 0/4
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit
  your product(config)# interface gigabitethernet 0/5
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit

At Switch6

• Configure the interface type as customerNetworkPort port-based.

your product(config)# interface gigabitethernet 0/2
your product(config-if)# bridge port-type customerNetworkPort port-based
your product(config-if)# exit

• Create the VLAN and make interfaces as member ports of this VLAN and Port P2 as untagged member.
  your product(config)# vlan 4
  your product(config-vlan)# ports gigabitethernet 0/2,0/3,0/4,0/5 untagged gigabitethernet 0/2
  your product(config-vlan)# exit

• Set the Primary Vlan (PVID) for an interface.
  your product(config)# interface gigabitethernet 0/2
  your product(config-if)# switchport pvid 4
  your product(config-if)# exit

• Configure the interface type as providerNetworkPort.
  your product(config)# interface gigabitethernet 0/3
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit
  your product(config)# interface gigabitethernet 0/4
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit
  your product(config)# interface gigabitethernet 0/5
  your product(config-if)# bridge port-type providerNetworkPort
  your product(config-if)# exit

SNMP Configurations

At Switch2

• Set the interface as customerEdgePort. [Index: Interface Number = 2]
  % snmp0 set {{ifMainBrgPortType.2 customerEdgePort }}

• Create the VLAN and make interfaces as member ports of this VLAN and Port P2 as untagged member.
  [Index: ContextID = 0, Vlan-ID = 4]
  % snmp0 set {{fsDot1qVlanStaticRowStatus.0.4 createAndWait }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 2]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.2 addUntagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 3]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.3 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 4]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.4 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 5]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.5 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4]
  % snmp0 set {{fsDot1qVlanStaticRowStatus.0.4 active }}

• Configure the CVID Registration table for interface with CVLAN to map with SVLAN.
  [Index: Interface Number = 2]
  % snmp0 set {{fsMIPbPortCVlan.2 2 }}
  [Index: Interface Number = 2, Vlan-ID =2]
  % snmp0 set {{dot1adMICVidRegistrationRowStatus.2.2 createAndWait }}
  % snmp0 set {{dot1adMICVidRegistrationSVid.2.2 4 }}
  % snmp0 set {{dot1adMICVidRegistrationUntaggedPep.2.2 false }}
  % snmp0 set {{dot1adMICVidRegistrationUntaggedCep.2.2 false }}
  % snmp0 set {{dot1adMICVidRegistrationRowStatus.2.2 active }}

• Configure the interface type as providerNetworkPort.
  [Index: Interface Number = 3]
  % snmp0 set {{ifMainBrgPortType.3 providerNetworkPort }}
  [Index: Interface Number = 4]
  % snmp0 set {{ifMainBrgPortType.4 providerNetworkPort }}
  [Index: Interface Number = 5]
  % snmp0 set {{ifMainBrgPortType.5 providerNetworkPort }}

At Switch6

• Configure the interface type as customerNetworkPortPortBased. [Index: Interface Number = 2]
  % snmp0 set {{ifMainBrgPortType.2 customerNetworkPortPortBased }}

• Create the VLAN and make interfaces as member ports of this VLAN and Port P2 as untagged member.
  [Index: ContextID = 0, Vlan-ID = 4]
  % snmp0 set {{fsDot1qVlanStaticRowStatus.0.4 createAndWait }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 2]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.2 addUntagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 3]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.3 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 4]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.4 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4, Interface Number = 5]
  % snmp0 set {{fsDot1qVlanStaticPort.0.4.5 addTagged }}
  [Index: ContextID = 0, Vlan-ID = 4]
  % snmp0 set {{fsDot1qVlanStaticRowStatus.0.4 active }}

• Set the Primary VLAN (PVID) for an interface. [Index: Interface Number = 2]
  % snmp0 set {{fsDot1qPvid.2 4 }}

• Configure interface type as providerNetworkPort
  [Index: Interface Number = 3]
  % snmp0 set {{ifMainBrgPortType.3 providerNetworkPort }}
  [Index: Interface Number = 4]
  % snmp0 set {{ifMainBrgPortType.4 providerNetworkPort }}
  [Index: Interface Number = 5]
  % snmp0 set {{ifMainBrgPortType.5 providerNetworkPort }}