half-duplex back pressure. FIFO Errors The number of packets dropped by this port due to an underflow in the transmit FIFO. When an underflow is detected, transmission is immediately aborted after sending a known invalid (inverted) CRC sequence. The

Ring type networks. If a frame received at an Ethernet port has a CFI set to 1, the frame should not be forwarded as-is to an untagged port. In the context of bandwidth regulation, DEI can be used

cfm add dmm cfm add dmm - Create a delay measurement Description: Create delay measurement for a MEP. Note: One-way delay measurements require time synchronization using NTP/PTP on units at each probe end. Syntax: cfm add dmm { {mep-idx

Orchestrator 24.09.1 No available upgrade. This is the latest release. See the Legacy Orchestrator 24.09.1 Release Notes to learn more. © 2026 Cisco and/or its affiliates. All rights reserved. For more information about trademarks, please

eir-max > 500000 | {cir-max } | {eir-max } }+ Parameters: Parameter Description cir Committed Information Rate in kbps. cbs Committed Burst Size in KiB. eir Excess Information Rate in kbps. ebs Excess Burst Size in KiB. cir-max Maximum Committed Information Rate

{src-mac-addr {disable | enable} } | {src-mac-mask } | {ethertype {disable | enable} } | {vlanstack-size {disable | enable}} | {vlan1-cfi {disable | enable}} | {vlan2-cfi {disable | enable}} | {vlan1-id {disable | enable}} | {vlan1-id-last {disable | enable}} | {vlan1-id-oper {lt | gt | eq | range

{fe-vlan1-priority {disable}} | {fe-vlan1-dei {disable}} | {fe-vlan1-id {disable}} | {fe-vlan2-priority {disable}} | {fe-vlan2-dei {disable}} | {fe-vlan2-id {disable}} | {fe-dscp-check {disable}} | {fe-dscp {disable}}} | {ooo-percentage-state {disable | enable}} | {ooo-percentage }}+ = A

established in step 3) on the server is required to accept and validate the server certificate. Using a Local Custom Certificate for Web Management If you prefer to use a local custom certificate for Web management, follow these recommended

MEG level and interface defined in the CLI using the reflector enable eth-oam meg-level interface command before reflection can operate correctly. Refer to the reflector section of the CLI guide for complete command usage and parameters. ▶

keystore for Skylight orchestrator version 24.09.1-GA ========================================================================================= Skylight orchestrator version 24.09.1-GA upgrade process was successful ========================================================================================= Post-Installation Procedures This section explains the procedures applicable after your upgrade. The post-installation procedures are: Reconfiguring the med

Header Settings Parameter Description VLAN Stack Size Enable this box, then make a selection in the drop-down list to indicate the number of VLAN tags that packets must have in order to match this filter. VLAN and VLAN-in

statistics clear statistics clear - clear all statistics Description: After issuing this command, the following statistics will be cleared: All ports statistics All policies statistics All bandwidth regulators statistics All OAM instances statistics Syntax: statistics clear © 2026 Cisco and/or

on port SFP-1-1. For this example, set the VLAN ID to 4001 and the Beacon settings to the values shown in the figure below. Notes: With the Auto option in IP config mode, the beaconer determines the IP

The unit’s management system provides multiple configurable management sessions to allow multiple users to control the unit. To view current sessions, access the page System ▶Session ▶Management . System ▶Session ▶Management For more information on specific values, refer to the

} }] } In this example, "example-endpoint-1" is used for both the endpoint ID, endpoint-name and as ne-id string. It is recommended to use this scheme unless there are reasons to do it differently. Matching rules for ne

Overview The Sensors UI is a management tool for configuring both Sensor Agents (formerly Skylight sensor: agents) and their sessions. View the Agents list by going to Sensors ► Agent . From here, you can observe your inventory and the status

You can reset the unit to its factory default settings either by using the button on the panel of the unit or by using the management Web interface. Each way is described below. Note: Only complete a “HARD RESET” when