Provider Connectivity Assurance
Support Portal
cisco.com
Login
Contents
x
Getting Started
Provider Connectivity Assurance
Legacy Orchestrator
Skylight Gateway
Assurance Sensor Agents
Assurance Sensor Capture
Assurance Sensor Control
Assurance Module Dock
Assurance Sensor Modules
Assurance Sensor SFP
Assurance Sensor GT-GT-S, LT-S, and LX-S
Assurance Sensor F100 and F25
Partner Enablement
Accedian Skylight Legacy Products and Documentation
Legal
Powered by
Getting Started
9 Articles
in this category
Contributors
+ 2
Share this
Print
Share
Contents
Getting Started
9 Articles
in this category
+ 2
Written by
Alan Chiu
,
Henrik Nydell
,
Andrea Hilton
and 2 others
Share
Setting up NSO with Provider Connectivity Assurance
In this article, we a look at how to set up Cisco Crosswork Network Services Orchestrator (NSO) to interwork with Provider Connectivity Assurance. Overview The configuration described in this article uses a locally-installed Docker version of ...
Written by
Alan Chiu
,
Henrik Nydell
,
Andrea Hilton
Updated on : 01 Nov 2024
Service Model
Service Model Overview When using the RESTCONF YANG interface to provision Provider Connectivity Assurance, the configuration is built according to the YANG service model described in this article. This model consists of three distinct tiers and a...
+ 1
Written by
Alan Chiu
,
Henrik Nydell
,
Andrea Hilton
and 1 others
Updated on : 01 Nov 2024
Service Endpoints
Service Endpoint The service-endpoint object defines the logical test endpoint for a test session and typically reference an interface or physical port. Both the source (sender) and destination (target/reflector) endpoints of a test session need t...
+ 1
Written by
Alan Chiu
,
Henrik Nydell
,
Andrea Hilton
and 1 others
Updated on : 27 Nov 2024
TWAMP and Metadata
TWAMP-Light RFC 5357 Sessions Endpoint Definition To set up TWAMP light test sessions using the RESTCONF YANG interface, you must first define the test endpoints. These endpoints, which are used for both TWAMP and sensor agent tests, utilize the...
+ 2
Written by
Alan Chiu
,
Jonathan Poole
,
Henrik Nydell
and 2 others
Updated on : 01 Nov 2024
Service Activation Testing (RFC 2544 and Y.1564)
RFC 2544 and Y.1564 Service Activation Tests Endpoint Definition To perform Service Activation Tests (SAT) using the RESTCONF YANG interface, you must first create the service-endpoints. The example below defines two Assurance Sensor SFP devic...
+ 2
Written by
Alan Chiu
,
Jonathan Poole
,
Henrik Nydell
and 2 others
Updated on : 01 Nov 2024
Session State and Threshold Crossing Notifications over RESTCONF
RESTCONF State and Threshold Alert Notifications The Provider Connectivity Assurance system delivers notifications over RESTCONF for two main event categories. State changes: for endpoints and sessions Threshold crossing alerts: for services...
+ 2
Written by
Alan Chiu
,
Jonathan Poole
,
Henrik Nydell
and 2 others
Updated on : 01 Nov 2024
How to Configure Agent Networking to Support Full IP Domain Isolation
The main purpose of IP domain isolation is to make sure every container running on the same host has the same IP configuration. This ensures the deployment is simple to understand. The diagram below illustrates how each TWAMP Session over L3VPN us...
Updated on : 27 Nov 2023
Accedian YANG Notifications Examples and Common Error Codes
This topic provides examples of Accedian YANG notifications and common error codes. For further information, questions, or clarifications regarding this release, contact the Accedian Technical Assistance Center (TAC) at skylight_tac@cisco.com. Not...
Updated on : 24 Jan 2024
RESTCONF Guide
Overview The gateway was made to uniformize the API of performance measurement (PM) for the Skylight portfolio. This solution is based on the yang modelling. The gateway is in charge of managing performance Sessions; it converts the Yang model to...
Updated on : 24 Jan 2024
Change password!
Changing your password will log you out immediately. Use the new password to log back in.
Current password
Current password is required
New password
New password must be at least 8 characters long. It should contain at least one upper and lower case letter, number, and a special character.
Confirm password
Confirm password must be at least 8 characters long. It should contain at least one upper and lower case letter, number, and a special character.
Confirm password should be same as new password
Update
Change profile
Success!
First Name
First name must have atleast 2 characters. Numbers and special characters are not allowed.
Last Name
Last name must have atleast 1 characters. Numbers and special characters are not allowed.
New email
Enter a valid email
Re-enter your password
Enter a valid password
Your profile has been successfully updated.
Update
Logout