Configuring ECFM in Single Instance Mode

The articles in this category describe the configuration guidelines for ECFM and Y.1731 in SI ( Single Instance ) mode. Configuration Guidelines The following commands must be executed in the specified sequence to start and configure the ECFM ...

This article describes the configuration of the CFM MD at a particular maintenance level. CLI Configurations To configure MD on the bridge Log in to the privileged EXEC mode. your product> enable Note: To log in to the User E...

This article describes the configuration of the CFM MA within a particular MD. Note: The MD must be configured prior to the configuration of MA. CLI Configurations To configure MA Execute the steps given in Configuring Maintena...

This article describes the configuration of the MEP. Note: The MD and MA must be configured prior to the configuration of the MEP. CLI Configurations To configure MEP Execute the steps given in SNMP Configurations for configu...

This article describes the configuration of the MIP (Maintenance Intermediate Point) on an interface. MIP can be configured on an interface using either of the following two methods: Explicit MIP Creation Implicit MIP Creation ...

This article describes the association of the VLANs with a Primary VLAN. The scope of the VLAN association is limited to ECFM entities only. CLI Configurations To associate a set of VLANs to a Primary VLAN Enter the global configuration ...

When Skylight Flex switch is made up, by default ECFM, it is in the start state, but operationally in disable state. That is, it does not generate, receive, or reply to any of the CFM PDUs. For Ethernet CFM entities to function, ECFM must be ena...

When the Skylight Flex switch is made up, by default ECFM, it is in the start state, but operationally in disable state, that is, it does not generate, receive or reply to any of the CFM PDUs once ECFM gets enabled. ECFM is enabled on all the inte...

By default, Y.1731 compliant features are in the disabled state. That is, it does not generate, receive or reply to any of the Y.1731 compliant CFM PDU(s). ECFM must be enabled for Y.1731 to start functioning. Y.1731 should be enabled for Y.1731...

By default, Y.1731 compliant features are in the disabled state, that is, it does not generate, receive or reply to any of the CFM PDU(s). ECFM must be enabled on the interface on which Y.1731 is to be enabled. CLI Configurations To enable Y....

By default, CCM offloading is in the disabled state. That is, it does not generate or receive the CCM PDU(s) through hardware. CLI Configurations To enable CCM offloading Enter into the global configuration mode. your product# configur...

After configuring and enabling Continuity Check Messages, every MEP (if MD, MA, and MEP are configured) transmits CC messages as per the CCM transmission interval that is set. CLI Configurations To configure and enable CCM Execute the st...

This article describes enabling crosschecking between the list of the configured remote MEP of a domain and the MEPs learned through the CCMs. By default, crosschecking is enabled. CLI Configurations To configure and enable crosschecking ...

After configuring and enabling LoopBack messages, every MEP (if MD, MA, and MEP are configured) can transmit LoopBack messages. CLI Configurations To configure loopback message Execute the steps given in section 3.3.3.1 for configuring MEP...

After configuring and enabling LTMs, every MEP (if MD, MA, and MEP are configured) can transmit LTMs. CLI Configurations To configure a linktrace message Execute the steps given in CLI Configurations to configure MEP before sending the L...

This article describes the steps to configure and enable the transmission and reception of TST PDU by an MEP. CLI Configurations To configure and enable test messages Execute the steps given in CLI Configurations to configure MEP befor...

This article describes the steps to configure and enable the transmission and reception of Frame delay PDU by an MEP. Frame Delay can be measured using either of the following methods: One-way Frame Delay Measurement Two-way Frame Delay Meas...

This article describes the steps to configure and enable the transmission and reception of Frame loss PDU by an MEP. Frame Loss can be measured using either of the following methods: Dual-ended using CCM messages Single-ended using LMM/LMR m...

This article describes the steps to configure and enable the transmission of AIS PDU by an MEP. CLI Configurations To configure and enable AIS message Execute the steps given in CLI Configurations to configure MEP before sending the AI...

This article describes the steps to configure and enable the transmission of LCK PDU by an MEP. CLI Configurations To configure and enable LCK message Execute the steps given in CLI Configurations to configure MEP before sending the LC...

This article describes the steps to configure and enable the Throughput Measurement by an MEP. Throughput Measurement can be measured using either of the following methods: One-way Throughput Measurement Two-way Throughput Measurement CL...

This article describes the steps required to configure the OUI globally on a device. CLI Configurations To configure the OUI globally on a device Enter into the global configuration mode your product# configure terminal Set the ...

This article describes the steps to enable the CFM PDU encapsulation in LLC header on the specified port. CLI Configurations To enable LLC encapsulation on a port Enter into the global configuration mode. your product# configure termin...

This article describes the viewing of information related to configured ECFM and Y.1731 entities in SI mode. CLI Configurations ECFM entities are displayed on the unit shell. ECFM provides the following show commands for displaying the ECFM enti...