Viewing VCA Bandwidth Regulator Statistics
  • 30 Mar 2022
  • 3 Minutes to read
  • Contributors
  • PDF

Viewing VCA Bandwidth Regulator Statistics

  • PDF

Article summary

To view traffic regulator statistics

  1. Access the page Virtual Connection ▶ VCA VLAN ▶ Configuration to view the configuration summary of all VCAs.

  2. On the top right, from the Remote Device drop-down list, select None.

  3. From the Filter drop-down list, select Remote Device Name.

  4. Click Search.

  5. In the BW Regulator Statistics column, click the VCA-VLAN's name.

The VCA bandwidth regulator statistics window will now display.

For more information on specific parameters, refer to the following table.

Bandwidth Regulator Statistics (Virtual Connection ▶ VCA ▶ Configuration ▶ BW Regulator Statistics)

ParameterDescription
NameThe name assigned to the regulator.
Accept bytesThe total number of bytes accepted by this regulator since the last time they have been cleared.
Accept packetsThe total number of frames accepted by this regulator since its creation.
Accept L1 rate (Mbps)The rate of accepted Layer-1 data, expressed in Mbps. This is the number of megabits of Layer-1 traffic accepted in the last second of transmission.
Accept L2 rate (Mbps)The rate of accepted Layer-2 data, expressed in Mbps. This is the number of megabits of Layer-2 traffic accepted in the last second of transmission.
Drop bytesThe total dropped bytes by this regulator since the statistical count started.
Drop packetsTotal dropped frames by this regulator since its creation
Drop L1 rate (Mbps)The rate of dropped Layer-1 data, expressed in Mbps.

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-1".

Drop L2 rate (Mbps)The rate of dropped Layer-2 data, expressed in Mbps.

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-2".

Green bytesThe total number of green bytes handled by this regulator since its creation.

Traffic that is declared green and complies with the CIR is allowed to pass through the policer without rate limitation. Green traffic in excess of this maximum is declared yellow by the regulator and is subject to EIR regulation.

Green packetsThe total number of green frames handled by this regulator since its creation.

Traffic that is declared green and complies with the CIR is allowed to pass through the policer without rate limitation. Green traffic in excess of this maximum is declared yellow by the regulator and is subject to EIR regulation.

Green L1 rate (Mbps)The rate of green Layer-1 data, expressed in Mbps .

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶Configuration page has been set to "Layer-1".

Green L2 rate (Mbps)The rate of green Layer-2 data, expressed in Mbps

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶Configuration page has been set to "Layer-2".

Yellow bytesThe total number of yellow bytes handled by this regulator since its creation. Yellow traffic in excess of this maximum is declared red by the regulator, then dropped.
Yellow packetsThe total number of yellow frames handled by this regulator since its creation. Yellow traffic in excess of this maximum is declared red by the regulator, then dropped.
Yellow L1 rate (Mbps)The rate of yellow Layer-1 data, expressed in Mbps

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-1".

Yellow L2 rate (Mbps)The rate of yellow Layer-2 data, expressed in Mbps

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-2".

Red bytesThe total number of red bytes handled by this regulator since its creation.
Red packetsThe total number of red frames handled by this regulator since its creation.
Red L1 rate (Mbps)The rate of red Layer-1 data, expressed in Mbps

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-1".

Red L2 rate (Mbps)The rate of red Layer-2 data, expressed in Mbps

Note: Only applies if the Regulator Working Rate parameter in the Traffic ▶ Configuration page has been set to "Layer-2".

© 2024 Cisco and/or its affiliates. All rights reserved.
 
For more information about trademarks, please visit: Cisco trademarks
For more information about legal terms, please visit: Cisco legal terms

For legal information about Accedian Skylight products, please visit: Accedian legal terms and tradmarks



Was this article helpful?

Changing your password will log you out immediately. Use the new password to log back in.
First name must have atleast 2 characters. Numbers and special characters are not allowed.
Last name must have atleast 1 characters. Numbers and special characters are not allowed.
Enter a valid email
Enter a valid password
Your profile has been successfully updated.