Configuring the EVPL Service Taking UNI traffic on One VLAN and Pushing Two VLAN

This use case explains how you can configure an EVPL service taking UNI traffic on one VLAN and pushing two VLAN towards the NNI port and reverse path with a pop two VLAN.

To configure an EVPL Service taking UNI traffic on one VLAN and pushing two VLAN towards the NNI port and reverse path with a pop two VLAN

1. Follow configuration below in Your Product-1 for UNI to NNI scenario:
   Your Product-1

Your Product# configure terminal
Your Product(config)# shutdown spanning-tree
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# no shutdown
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# no shutdown
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# no shutdown
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# bridge port-type customerEdgePort 
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# bridge port-type customerEdgePort 
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# bridge port-type providerNetworkPort three-tagged
Your Product(config-if)# switchport egress ether-type 0x88a8
Your Product(config-if)# switchport egress inner-ether-type 0x8100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# no interface vlan 1
Your Product(config)# end
Your Product# configure terminal
Your Product(config)# vlan 100
Your Product(config-vlan)# ports xl-ethernet 0/1 xl-ethernet 0/2 untagged gigabitethernet 0/1
Your Product(config-vlan)# end
Your Product(config)# vlan 200
Your Product(config-vlan)# ports xl-ethernet 0/3 xl-ethernet 0/2 untagged gigabitethernet 0/3
Your Product(config-vlan)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# switchport customer-vlan 10 service-vlan 100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# switchport customer-vlan 20 service-vlan 200
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# switchport three-tagged-pnp tunnel vlan 1000
Your Product(config-if)# switchport three-tagged-pnp tunnel ethertype 0x9100
Your Product(config-if)# switchport three-tagged-pnp tunnel priority 7
Your Product(config-if)# switchport three-tagged-pnp tunnel use-dei true
Your Product(config-if)# end

2. Check EtherType status:

show three-tagged-pnp vlan config

Sample output:

Your Product# show three-tagged-pnp vlan config
Switch default

Port   Tunnel   Tunnel        Tunnel    Tunnnel
              VLAN   EtherType   Priority   CFI/DEI
---------------------------------------------
Gi0/2     1000    0x9100           7         1      

3. Check the port configuration status:

show vlan port config port xl-ethernet 0/2

Sample Output:

Your Product# show vlan port config port xl-ethernet 0/2

Switch default

Vlan Port configuration table

-------------------------------

Port Gi0/2
Bridge Port Type                    : Three Tagged PNP Port
 Port Vlan ID                        : 1
 Port Acceptable Frame Type          : Admit All
 Port Mac Learning Status            : Enabled
 Port Ingress Filtering              : Disabled
 Port Mode                           : Hybrid
 Port Gvrp Status                    : Disabled
 Port Gmrp Status                    : Disabled
 Port Gvrp Failed Registrations      : 0
 Gvrp last pdu origin                : 00:00:00:00:00:00   
 Port Restricted Vlan Registration   : Disabled
 Port Restricted Group Registration  : Disabled
 Mac Based Support                   : Disabled
 Subnet Based Support                : Disabled
 Port-and-Protocol Based Support     : Enabled
 Default Priority                    : 0
 Filtering Utility Criteria          : Default
Port Protected Status               : Disabled
 Inner Tag Ingress EtherType         : 0x88a8
 Inner Tag Egress EtherType          : 0x8100
 Outer Tag Ingress EtherType         : 0x9100
 Outer Tag Egress EtherType          : 0x88a8
  Egress TPID Type                    : Portbased
 Allowable TPID 1                    : 0x0
 Allowable TPID 2                    : 0x0
 Allowable TPID 3                    : 0x0

Reflection Status                   : Disabled

-------------------------------------------------------
Your Product#

4. Remove the UNI to NNI configuration and follow configuration for NNI to UNI.

Your Product#configure terminal
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# no switchport customer-vlan 10 
Your Product(config-if)# end
Your Product#configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# no switchport customer-vlan 20 
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# vlan 100
Your Product(config-vlan)# no ports xl-ethernet 0/1 xl-ethernet 0/2 untagged gigabitethernet 0/1
Your Product(config-vlan)# end
Your Product(config)# vlan 200
Your Product(config-vlan)# no ports xl-ethernet 0/3 xl-ethernet 0/2 untagged gigabitethernet 0/3
Your Product(config-vlan)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# no switchport egress ether-type
Your Product(config-if)# no switchport egress inner-ether-type
Your Product(config-if)# end

5. Configure configurations below for NNI to UNI.

Your Product#configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# bridge port-type providerNetworkPort three-tagged
Your Product(config-if)# switchport ingress ether-type 0x88a8
Your Product(config-if)# switchport ingress inner-ether-type 0x8100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# bridge port-type customerEdgePort 
Your Product(config-if)# switchport egress ether-type 0x8100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# bridge port-type customerEdgePort 
Your Product(config-if)# switchport egress ether-type 0x8100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# vlan 100
Your Product(config-vlan)# ports xl-ethernet 0/1 xl-ethernet 0/2  untagged gigabitethernet 0/1
Your Product(config-vlan)# end
Your Product# configure terminal
Your Product(config)# vlan 200
Your Product(config-vlan)# ports xl-ethernet 0/3 xl-ethernet 0/2  untagged xl-ethernet 0/3
Your Product(config-vlan)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/1
Your Product(config-if)# switchport customer-vlan 10 service-vlan 100
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/3
Your Product(config-if)# switchport customer-vlan 20 service-vlan 200
Your Product(config-if)# end
Your Product# configure terminal
Your Product(config)# interface xl-ethernet 0/2
Your Product(config-if)# switchport three-tagged-pnp tunnel vlan 1000
Your Product(config-if)# switchport three-tagged-pnp tunnel ethertype 0x9100
Your Product(config-if)# switchport three-tagged-pnp tunnel priority 7
Your Product(config-if)# switchport three-tagged-pnp tunnel use-dei true
Your Product(config-if)# end

6. Check EtherType status:

show three-tagged-pnp vlan config

Sample output:

Your Product# show three-tagged-pnp vlan config
Switch default

Port   Tunnel   Tunnel        Tunnel    Tunnnel
              VLAN   EtherType   Priority   CFI/DEI
---------------------------------------------
Gi0/2     1000    0x9100           7         1    

7. Check the port configuration status:

show vlan port config port xl-ethernet 0/2

Sample Output:

Your Product# show vlan port config port xl-ethernet 0/2

Switch default

Vlan Port configuration table

-------------------------------
Port Gi0/2
 Bridge Port Type                    : Three Tagged PNP Port
 Port Vlan ID                        : 1
 Port Acceptable Frame Type          : Admit All
 Port Mac Learning Status            : Enabled
 Port Ingress Filtering              : Disabled
 Port Mode                           : Hybrid
 Port Gvrp Status                    : Disabled
 Port Gmrp Status                    : Disabled
 Port Gvrp Failed Registrations      : 0
 Gvrp last pdu origin                : 00:00:00:00:00:00   
 Port Restricted Vlan Registration   : Disabled
 Port Restricted Group Registration  : Disabled
 Mac Based Support                   : Disabled
 Subnet Based Support                : Disabled
 Port-and-Protocol Based Support     : Enabled
 Default Priority                    : 0
 Filtering Utility Criteria          : Default
Port Protected Status               : Disabled
 Inner Tag Ingress EtherType         : 0x8100
 Inner Tag Egress EtherType          : 0x8100
 Outer Tag Ingress EtherType         : 0x88a8
 Outer Tag Egress EtherType          : 0x88a8
  Egress TPID Type                    : Portbased
 Allowable TPID 1                    : 0x0
 Allowable TPID 2                    : 0x0
 Allowable TPID 3                    : 0x0
 
 Reflection Status                   : Disabled
 
 -------------------------------------------------------
Your Product#