y1564 add test
y1564 add test - Create an instance of Y.1564 test
Description:
With y1564 add test, you can create a new Y.1564 test and set its parameters.
Syntax:
y1564 add test <test-name> {
{description <string>} |
{configuration {enable | disable}} |
{step-duration {1-60} |
{performance {enable | disable}} |
{test-duration {1-1440} |
{parallel {enable | disable}} |
{burst-sla {enable | disable}} |
{port <port-name>} |
{delay-type {one-way-delay | two-way-delay}} |
{time-sync-mandatory {enable | disable}} |
{packet-type {layer-2|layer-3| l2-accedian| l2-generic}} |
{dst-ipv4-addr <ip-addr>} |
{destination-port <0-65535>} |
{source-port <0-65535>} |
{dscp <0-63>} |
{dst-mac-addr <mac-addr>} |
{y1731-level <0-7>}}+
{dst-ipv4-addr <ip-addr>} |
{destination-port <0-65535>} |
{source-port <0-65535>} |
{dscp <0-63>} |
{dst-mac-addr <mac-addr>} |
{y1731-level <0-7>}}+
Parameters:
| Parameter | Description |
|---|---|
| description | Short description of the Y.1564 test. |
| configuration | Enable Y.1564 configuration test. |
| step-duration | Duration of each step during the configuration test in seconds. |
| performance | Enable Y.1564 performance test. |
| test-duration | Duration of each step during the performance test in minutes. |
| parallel | Enable Y.1564 parallel service configuration test. |
| burst-sla | Enable Y.1564 burst SLA test. |
| port | Name of the port to which to send the test traffic. |
| delay-type | Type of delay measurement. |
| time-sync-mandatory | Enable time synchronization verification. |
| packet-type | Used to define specific fields in the test packet. |
| dst-ipv4-addr | The IPv4 destination address. |
| destination-port | The destination port for UDP protocol (0 - 65535). |
| source-port | The source port for UDP protocol (0 - 65535). |
| dscp | The Diff-Serv CodePoint value (0 - 63). |
| dst-mac-addr | This is the Ethernet MAC destination address. |
| y1731-level | Y.1731 Maintenance Entity Group level (0-7). |
y1564 delete report
y1564 delete report - Delete an instance of Y.1564 test report
Description:
Delete an instance of Y.1564 test report.
Syntax:
y1564 delete report <report-name>
<report-name> = <string>
Parameters:
| Parameter | Description |
|---|---|
| <report-name> | A unique name to identify an instance of Y.1564 test report. |
y1564 delete test
y1564 delete test - Delete an instance of Y.1564 test
Description:
Delete an instance of Y.1564 test.
Syntax:
y1564 delete test <test-name>
<test-name> = <string>
Parameters:
| Parameter | Description |
|---|---|
| <test-name> | A unique name to identify an instance of Y.1564 test. |
y1564 edit report
y1564 edit report - Change Y.1564 test activation information
Description:
After a Y.1564 test has completed, the report can be edited to modify or add information such as: name, description, note, technician's name.
Syntax:
y1564 edit report filename <filename> {
{description <desc>} |
{note <note>} |
{technician <tech. name>}}+
<filename> - <string> Unique filename associated with the activation.
Parameters:
| Parameter | Description |
|---|---|
| description | <string> Information about the test being described. |
| note | <string> Additional information about the test being described. |
| technician | <string> Name of technician executing the test. |
y1564 edit service
y1564 edit service - Change Y.1564 service configuration
Description:
With y1564 edit service, you change the configuration of a service under a specific test.
Syntax:
y1564 edit service <test-name> <service-id> {
{name <service-name>} |
{state {enable | disable}} |
{policing {enable | disable}} |
{step {enable | disable}} |
{availability {enable | disable}} |
{cir <0 to max-port-speed>} |
{cbs <0 to 10000>} |
{eir <0 to max-port-speed>} |
{ebs <8>}|
{size-type {fixed}} |
{packet-size <64 to 10240>} |
{ftd <decimal>} |
{ftd-type {max|avg}} |
{fdv <decimal>} |
{fdv-type {max|avg}} |
{flr <exponent>} |
{m-factor <decimal>} |
{dst-ipv4-overwrite {enable|disable}} |
{dst-ipv4-addr <ip-addr>} |
{dscp-overwrite {enable|disable}} |
{dscp <0-63>} |
{dst-mac-addr-overwrite {enable|disable}} |
{dst-mac-addr <mac-addr> } |
{y1731-level-overwrite {enable|disable}} |
{y1731-level <0-7>} |
{vlan1-header {enable|disable}} |
{vlan1-ethertype {c-vlan|s-vlan}} |
{vlan1-priority <0-7>} |
{vlan1-id <0-4095>} |
{vlan1-cfi <0-1>} |
{vlan2-header {enable|disable}} |
{vlan2-ethertype {c-vlan|s-vlan}} |
{vlan2-priority <0-7>} |
{vlan2-cfi <0-1>} |
{vlan2-id <0-4095>} |
{fe-vlan1-priority-check {disable | enable}} |
{fe-vlan1-dei-check {disable | enable}} |
{fe-vlan1-id-check {disable | enable}} |
{fe-vlan2-priority-check {disable | enable}} |
{fe-vlan2-dei-check {disable | enable}} |
{fe-vlan2-id-check {disable | enable}} |
{fe-dscp-check {disable | enable}} |
{fe-vlan1-priority <0-7> {disable | enable}} |
{fe-vlan1-dei <0-1> {disable | enable}} |
{fe-vlan1-id <0-4095> {disable | enable}} |
{fe-vlan2-priority <0-7> {disable | enable}} |
{fe-vlan2-dei <0-1> {disable | enable}} |
{fe-vlan2-id <0-4095> {disable | enable}} |
{fe-dscp <0-63> {disable | enable}}}+
<test-name> = A unique name used to identify a Y.1564 test in the system.
<service-id> = A unique id used to identify a service in this test.
Parameters:
| Parameter | Description |
|---|---|
| name | The name of a service. |
| disable | enable | To enable or disable the field in the check. |
| state | Enable this service for this specific test. |
| policing | Enable policing testing. |
| step | Enable step testing. |
| availability | Enable Availability measurement. |
| cir | Committed information rate in kbps. |
| cbs | Committed burst size in KiB (1024 bytes). |
| eir | Excess information rate in kbps. |
| ebs | Excess burst size in KiB (1024 bytes). |
| size-type | Packet sizes are limited to fixed only, no support for EMIX available in this product. |
| packet-size | For a fixed packet, specify the packet size. Maximum packet size is 10240. |
| ftd | Maximum/average two-way Frame Transfer Delay (FTD) allowed (in microseconds). |
| ftd-type | Determines whether the Frame Transfer Delay (FTD) parameter is a maximum or average value. |
| fdv | Maximum/average two-way Frame Delay Variation (FDV) allowed (in microseconds). |
| fdv-type | Determines whether the Frame Delay Variation (FDV) parameter is a maximum or average value. |
| flr | Maximum Frame Loss Ratio (FLR) allowed. |
| m-factor | The M factor is added to the Service Acceptance Criteria in the policing test to account for the effect of the CBS and EBS on the total rate. The policing test will pass if IR-T=<CIR+EIR+M. Where:
|
| dst-ipv4-overwrite | Overwrite the test IPv4 address with the service address. |
| dst-ipv4-addr | The IPv4 destination address. |
| dscp-overwrite | Overwrite the test DSCP value with the service value. |
| dscp | The Diff-Serv CodePoint value (0 - 63). |
| mac-addr-overwrite | Enable/Disable the overwrite of the test destination MAC address. |
| mac-addr | The destination MAC address to overwrite. |
| y1731-level-overwrite | Enable/Disable the overwrite of the Y.1731 MEG level. |
| y1731-level | Y.1731 MEG level value to overwrite. |
| vlan1-header | Enable the presence of the first VLAN header. |
| vlan1-ethertype* | First VLAN protocol ID set to C-VLAN (0x8100) for 802.1Q network, T-VLAN (0x9100) for 802.1Q tunneling network, or S-VLAN (0x88A8) for 802.1AD network. |
| vlan1-cfi | First VLAN CFI/DEI may be 0 or 1. It is usually set to 0. |
| vlan1-id | First VLAN ID may be any value between 0 and 4095. |
| vlan1-priority | First VLAN priority can be between 0 and 7, 7 being the highest priority. Normal traffic has priority 0. |
| vlan2-header | Enable the presence of the second VLAN header. |
| vlan2-ethertype* | Second VLAN protocol ID set to C-VLAN (0x8100) for 802.1Q network, T-VLAN (0x9100) for 802.1Q tunneling network, or S-VLAN (0x88A8) for 802.1AD network. |
| vlan2-cfi | Second VLAN CFI/DEI may be 0 or 1. It is usually set to 0. |
| vlan2-id | Second VLAN ID may be any value between 0 and 4095. |
| vlan2-priority | Second VLAN priority can be between 0 and 7, 7 being the highest priority. Normal traffic has priority 0. |
| fe-no-vlan1-check | Enable this option if you want to validate that the frames received at the far-end do not have a first VLAN tag (i.e., untagged). |
| fe-vlan1-priority-check | Enable the far-end verification of the first VLAN priority. |
| fe-vlan1-dei-check | Enable the far-end verification of the first VLAN DEI. |
| fe-vlan1-id-check | Enable the far-end verification of the first VLAN ID. |
| fe-no-vlan2-check | Enable this option if you want to validate that the frames received at the far-end do not have a second VLAN tag (i.e., untagged). |
| fe-vlan2-priority-check | Enable the far-end verification of the second VLAN priority. |
| fe-vlan2-dei-check | Enable the far-end verification of the second VLAN DEI. |
| fe-vlan2-id-check | Enable the far-end verification of the second VLAN ID. |
| fe-dscp-check | Enable the far-end verification of the DSCP value. |
| fe-vlan1-priority | If enabled, this is the first VLAN priority value expected at the far-end. |
| fe-vlan1-dei | If enabled, this is the first VLAN DEI value expected at the far-end. |
| fe-vlan1-id | If enabled, this is the first VLAN ID value expected at the far-end. |
| fe-vlan2-priority | If enabled, this is the second VLAN priority value expected at the far-end. |
| fe-vlan2-dei | If enabled, this is the second VLAN DEI value expected at the far-end. |
| fe-vlan2-id | If enabled, this is the second VLAN ID value expected at the far-end. |
| fe-dscp | If enabled, this is the DSCP value expected at the far-end DSCP. |
*The value of s-vlan is defined by the global S-VLAN setting.
y1564 edit test
y1564 edit test - Change an Y.1564 test configuration
Description:
With y1564 edit test, you can change the parameters of an existing test.
Syntax:
y1564 edit test <test-name> {
{name <test-name>} |
{description <string>} |
{configuration {enable | disable}} |
{step-duration {1-60} |
{performance {enable | disable}} |
{test-duration {1-1440} |
{parallel {enable | disable}}
{burst-sla {enable | disable}} |
{port <port-name>} |
{delay-type {one-way-delay | two-way-delay}} |
{time-sync-mandatory {enable | disable}} |
{packet-type {layer-2| layer-3| l2-accedian| l2-generic}} |
{dst-ipv4-addr <ip-addr>} |
{destination-port <0-65535>} |
{source-port <0-65535>} |
{dscp <0-63>} |
{dst-mac-addr <mac-addr>} |
{y1731-level <0-7>}}+
Parameters:
| Parameter | Description |
|---|---|
| name | The name of the test. |
| description | Short description of the Y.1564 test. |
| configuration | Enable Y.1564 configuration test. |
| step-duration | Duration of each step during the configuration test in seconds. |
| performance | Enable Y.1564 performance test. |
| test-duration | Duration of each step during the performance test in minutes. |
| parallel | Enable Y.1564 parallel service configuration test. |
| burst-sla | Enable Y.1564 burst SLA test. |
| port | Name of the port to which to send the test traffic. |
| delay-type | Type of delay measurement. |
| time-sync-mandatory | Enable time synchronization verification. |
| packet-type | Used to define specific fields in the test packet. |
| dst-ipv4-addr | The IPv4 destination address. |
| destination-port | The destination port for UDP protocol (0 - 65535). |
| source-port | The source port for UDP protocol (0 - 65535). |
| dscp | The Diff-Serv CodePoint value (0 - 63). |
| dst-mac-addr | This is the Ethernet MAC destination address. |
| y1731-level | Y.1731 Maintenance Entity Group level (0-7). |
y1564 generate report
y1564 generate report - Generate a Y.1564 report file
Description:
This command allows to generate a Y.1564 test report.
Syntax:
y1564 generate report <filename> [report-type {report-type-txt |
report-type-xml}]
Parameters:
| Parameter | Description |
|---|---|
| filename | <string> Unique filename associated with the report. |
| report-type | Report type (XML, TXT) to generate. |
y1564 show activation
y1564 show activation - Show the Y.1564 test activation
Description:
This command displays the Y.1564 test activation. i.e. its name, status and description. If a specific test name is specified, a full test activation will be displayed (name, status, service name, and progression of each test step).
Syntax:
y1564 show activation <filename>
Parameters:
| Parameter | Description |
|---|---|
| <filename> | <string> Unique filename associated with the activation. |
y1564 show service configuration
y1564 show service configuration - Show Y.1564 service configuration
Description:
The command displays the configuration for a specific service.
Syntax:
y1564 show service configuration <test-name> <service-id>
Parameters:
| Parameter | Description |
|---|---|
| <test-name> | A unique name used to identify a Y.1564 in the system. |
| <service-id> | A unique id used to identify a service in this test. |
y1564 show test configuration
y1564 show test configuration - Show Y.1564 test configuration
Description:
This command displays the Y.1564 test configuration. Specifying a test name provides detailed configuration about this test. Otherwise, the command provides a summary of the configured test.
Syntax:
y1564 show test configuration <test-name>
Parameters:
| Parameter | Description |
|---|---|
| <test-name> | <string> Name of the specific test to display the configuration. |
y1564 start activation
y1564 start activation - Starts a Y.1564 test
Description:
This command starts the specified Y.1564 test and creates a new report.
Syntax:
y1564 start activation filename <filename> test <report-test>
{ {description <report-desc>} |
{technician <report-tech>} |
{note <report-note>} }+
Parameters:
| Parameter | Description |
|---|---|
| filename | <string> Unique filename for the report. |
| test | <string> Name for the Y.1564 test to run. |
| description | <string> Description for this report. |
| technician | <string> Name of the technician running this test. |
| note | <string> Note associated to this test. This note will be included in the report. |
y1564 stop activation
y1564 stop activation - Stop a Y.1564 test
Description:
This command stops the execution of the specified test.
Syntax:
y1564 stop activation filename <filename>
Parameters:
| Parameter | Description |
|---|---|
| filename | <string> Unique filename where the report will be stored. |
y1564 upload report
y1564 upload report - Upload a Y.1564 report file
Description:
This command allows to upload a Y.1564 test report to a remote location.
Syntax:
y1564 upload report <filename> <url> [report-type {report-type-txt |
report-type-xml}]
Parameters:
| Parameter | Description |
|---|---|
| filename | <string> Unique filename associated with the report. |
| url | URL to reach the server and directory, e.g.
|
| report-type | Report type (XML, TXT) to upload to server. |
Note: This command does not support passwords that include the “@” character.
© 2026 Cisco and/or its affiliates. All rights reserved.
For more information about trademarks, please visit: Cisco trademarks
For more information about legal terms, please visit: Cisco legal terms
For legal information about Accedian Skylight products, please visit: Accedian legal terms and trademarks