Adding, Editing and Deleting Devices Manually
  • 21 Jun 2024
  • 4 Minutes to read
  • Contributors
  • PDF

Adding, Editing and Deleting Devices Manually

  • PDF

Article summary

You can add new devices or edit existing devices in the Managed Elements tab; including:

  • Skylight elements
  • Skylight sensor: modules (smart SFPs and ANT devices)
  • Skylight sensor: control

To add or edit Skylight devices manually

  1. Access the Managed Elements page by selecting Devices ▶ Managed Elements. A list of all devices managed by Skylight orchestrator is displayed.

  2. Click the Add Button_New_Generic.png button on the toolbar to add a new device or double-click an existing device to configure its parameters. The Device configuration dialog appears.

  3. Complete the fields at the top of the dialog as necessary. For more information on how to complete the fields, see the table "Device configuration dialog - Parameters".

  4. Click the Save button, then Close.

For devices that have their own inventory of modules, you may need to load their inventory. For more information, see "Loading the Inventory of Performance Elements".

Device configuration dialog - Parameters

ParameterDescription
Managed stateDetermines whether the Skylight device is currently being managed by Skylight orchestrator.

Possible values:

  • Managed: Skylight orchestrator actively maintains a connection to the Skylight device. The device will be displayed in the Managed Element page.
  • Unmanaged: Skylight orchestrator does not maintain a connection to the Skylight device. The device will be displayed in the Unmanaged Element page.
CredentialThe name of the Credential that Skylight orchestrator uses to log on to this Skylight device. See "Setting Up Credentials for Performance Elements".
ResyncDetermines whether Skylight orchestrator will periodically synchronize the configuration information that it stores for this Skylight device (such as Inventory, Performance Monitoring Configuration and Y.1564 Test Configuration) with the configuration information stored on the Skylightdevice itself.

Possible values:

  • Enabled: Skylight orchestrator will periodically synchronize configuration information with the Skylight device.
  • Disabled: Skylight orchestrator will not periodically synchronize configuration information with the Skylight device.
LabelAn identifier for the device that is defined and used in Skylight orchestrator.
IP addressThe IP address of the Skylight device. This is an editable field. You can change the IP address, if necessary.
PortMust be set to 22 (SSH remote login for CLI).
Enable Inventory Polling?This checkbox determines whether or not Skylight orchestrator will poll this device periodically for its inventory.

Note: This checkbox does not determine whether this device is an inventory tracker. That can only be set on the Skylight device itself. It is possible to log on to the device from Skylight orchestrator (by clicking the link for its IP address) in order to set or check if it is an inventory tracker.

Possible values:

  • Checked (enabled): Skylight orchestrator will automatically poll this device for new devices that it has discovered.

Only devices with the Plug & Go feature enabled can be automatically detected in this way.

Detected devices will be added to the Unmanaged Elements list. The Source Inventory field of these devices will be set to Plug & Go

Skylight orchestrator will poll this inventory tracker every five minutes.

  • Unchecked (disabled): Skylight orchestrator will not poll this device for new devices that it has detected.

Checking the Connection to a Devices

To test the SSH connection between Skylight orchestrator and a device

  1. Access the page Devices ▶ Managed Elements or Devices ▶ Unmanaged Elements.

  2. Double-click a Skylight device to access its Device configuration.

  3. Click the Verify Device Config Button_Verify_Device_Config.png button on the toolbar to verify that Skylight orchestrator can connect to the device using the configuration information set in the dialog.

  4. After a short delay, check the test results that are displayed to the right of the button, as shown below.

  5. Click Save to save the device details.

  6. Close the Device configuration dialog to return to the Discovery page.

Changing the Management State of a Device

A device can be in either of the following management states:

  • Managed: You can perform all other operations (PM, test, upgrades, etc.) on the device.
  • Unmanaged: You are restricted to basic operations (delete, manage, etc.) that can be performed on the device.

To change the state of a device (Managed to Unmanaged)

  1. Access the page Devices ▶ Managed Elements.

  2. Select one or more devices from the list.

  3. Click the Unmanage devices Button_Unmanage_Devices.png button.

  4. In the confirmation dialog, click OK to confirm and apply.

The devices are removed from the Managed Elements list and are added to the Unmanaged Elements list.

To change the state of a device (Unmanaged to Managed)

  1. Access the page Devices ▶ Unmanaged Elements.

  2. Select one or more devices from the list.

  3. Click the Manage devices Button_Manage_Devices.png button.

  4. In the confirmation dialog, click OK to confirm and apply.

The devices are removed from the Unmanaged Elements list and are added to the Managed Elements list.

Alternatively, you can double-click a device to access the Device configuration page, where you can change the Managed state from Managed to Unmanaged or from the reverse (Unmanaged to Managed).

Deleting a Device

To be able to delete a device from the Skylight orchestrator server, you first need to put it into an Unmanaged state.

To delete a device

  1. Access the page Devices ▶ Unmanaged Elements.

  2. Select a device and click the Remove devices Button_Remove_Generic.png button on the toolbar.

  3. In the confirmation dialog, click OK to confirm and apply your changes.

All data pertaining to the device is permanently removed from Skylight orchestrator.

© 2024 Cisco and/or its affiliates. All rights reserved.
 
For more information about trademarks, please visit: Cisco trademarks
For more information about legal terms, please visit: Cisco legal terms

For legal information about Accedian Skylight products, please visit: Accedian legal terms and tradmarks



Was this article helpful?

Changing your password will log you out immediately. Use the new password to log back in.
First name must have atleast 2 characters. Numbers and special characters are not allowed.
Last name must have atleast 1 characters. Numbers and special characters are not allowed.
Enter a valid email
Enter a valid password
Your profile has been successfully updated.